Author Topic: my new toy  (Read 310 times)

daydreamer

  • Member
  • ****
  • Posts: 548
  • reach for the stars
my new toy
« on: September 13, 2018, 04:40:00 AM »
Ti84 calculator

« Last Edit: September 14, 2018, 06:44:11 PM by daydreamer »
Quote from Flashdance
Nick  :  When you give up your dream, you die.
*wears a flameproof asbestos suit*

daydreamer

  • Member
  • ****
  • Posts: 548
  • reach for the stars
Re: my new toy
« Reply #1 on: September 24, 2018, 04:34:15 AM »
Got two apps on it, geographic and periodic
Backed it up, took screenshot, entered some variables
« Last Edit: September 24, 2018, 02:34:14 PM by daydreamer »
Quote from Flashdance
Nick  :  When you give up your dream, you die.
*wears a flameproof asbestos suit*

daydreamer

  • Member
  • ****
  • Posts: 548
  • reach for the stars
Re: my new toy
« Reply #2 on: September 28, 2018, 03:37:02 AM »
the best part is Asm(,AsmComp(,AsmPrgm
I don't know if it should be possible with MASM macro capability or its a little /big endian problem?
anyone tried calculator asm programming? or at least Z80 asm?
Quote from Flashdance
Nick  :  When you give up your dream, you die.
*wears a flameproof asbestos suit*

FORTRANS

  • Member
  • *****
  • Posts: 1025
Re: my new toy
« Reply #3 on: September 28, 2018, 10:13:23 PM »
Hi,

   I did some 8088/Z80 assembly on a Heath/Zenith Z-90 a
long time ago.  The operating system was HDOS.

Cheers,

Steve N.

daydreamer

  • Member
  • ****
  • Posts: 548
  • reach for the stars
Re: my new toy
« Reply #4 on: September 29, 2018, 02:55:10 AM »
Hi,

   I did some 8088/Z80 assembly on a Heath/Zenith Z-90 a
long time ago.  The operating system was HDOS.

Cheers,

Steve N.
I have zero experience with z80,lots of experience in 6502 instead
its built from the first intel 8bit and do you think it should be possible to just use a macro assembler to assemble mov's as LD's and equate mostly used registers as equates?I know its possible reprogram keywords
maybe as start convert some 16bit x86 tiny programs?
Hutch?
does calculator have a blitter to just make a single call to hardware?
Quote from Flashdance
Nick  :  When you give up your dream, you die.
*wears a flameproof asbestos suit*

FORTRANS

  • Member
  • *****
  • Posts: 1025
Re: my new toy
« Reply #5 on: October 01, 2018, 04:39:08 AM »
Hi,

I have zero experience with z80,lots of experience in 6502 instead
its built from the first intel 8bit and do you think it should be possible to just use a macro assembler to assemble mov's as LD's and equate mostly used registers as equates?I know its possible reprogram keywords

   It should be possible to do that, but it would be a lot of work.
Even more work to do it well.  Jochen, Hutch, and others that write
fancy macros should be able to comment more on how feasible
it could be.

   A better idea would be to use an existing cross assembler.
Maybe search the old MS-DOS software repositories (perhaps
using archive.org).

   The best, if unlikely, idea would be to search TI's site for a
development kit or tool for your specific device.  (Good luck!)
Maybe there is a forum or newsgroup dedicated to your
calculator?

Regards,

Steve

daydreamer

  • Member
  • ****
  • Posts: 548
  • reach for the stars
Re: my new toy
« Reply #6 on: October 08, 2018, 04:08:08 AM »
Hi,

I have zero experience with z80,lots of experience in 6502 instead
its built from the first intel 8bit and do you think it should be possible to just use a macro assembler to assemble mov's as LD's and equate mostly used registers as equates?I know its possible reprogram keywords

   It should be possible to do that, but it would be a lot of work.
Even more work to do it well.  Jochen, Hutch, and others that write
fancy macros should be able to comment more on how feasible
it could be.

   A better idea would be to use an existing cross assembler.
Maybe search the old MS-DOS software repositories (perhaps
using archive.org).

   The best, if unlikely, idea would be to search TI's site for a
development kit or tool for your specific device.  (Good luck!)
Maybe there is a forum or newsgroup dedicated to your
calculator?

Regards,

Steve
thanks Steve

Code: [Select]
PROGRAM:FIBONNAC
1->C
2->D
for(B,0,1000)
Disp B,C,D
D+C->C
C+D->D
End
« Last Edit: October 16, 2018, 03:57:03 PM by daydreamer »
Quote from Flashdance
Nick  :  When you give up your dream, you die.
*wears a flameproof asbestos suit*